BTR Stage 2 vs Stage 3 — Which Cam for Your VE Commodore?

Author: Lucky  

The two most common BTR cams for VE Commodore LS3 and L98 builds are Stage 2 and Stage 3. People ask which one constantly. The honest answer: it depends on the build. But here's how to work out which applies to yours.

What the Specs Actually Mean

SpecStage 2 V2Stage 3 V2
Intake duration221°227°
Exhaust duration24X° (BTR proprietary)24X° (BTR proprietary)
Intake lift.624".636"
Exhaust lift.636".636"
LSA112°111.5°
RPM range1,800–6,600 RPM2,200–6,800 RPM
Idle qualityMild lopeNoticeable lope

Six degrees of intake duration and a slightly tighter LSA is the actual difference. That tighter LSA on the Stage 3 sharpens the mid-range and top-end hit — but it also moves the idle vacuum down and makes the lope more pronounced. The RPM floor goes up: Stage 3 doesn't like sitting at 1,800 RPM doing school pickups.

The VE Commodore Context

VE Commodores run either the L98 (6.0L Gen IV, AFM equipped) or the LS3 (6.2L Gen IV, non-AFM). Both take these cams, but the L98 needs AFM deleted before the cam goes in — the AFM lifters and BTR cam do not play well together. That's a separate job and adds to the total cost.

The LS3 is a cleaner install. No AFM, stiffer factory springs, and it responds well to both Stage 2 and Stage 3 depending on the rest of the build.

Stage 2 — Who It Suits

Stage 2 is the cam for a VE Commodore that still drives every day. Mild lope, 1,800 RPM floor, factory torque converter compatible. If the car has a cold air intake, headers, and a tune — Stage 2 gives you the cam-on feel without sacrificing low-speed drivability or forcing a converter change.

Stage 2 verdict: Street build. Daily driver or weekend car that still sees traffic. Running factory converter. Wants the sound and feel without compromising driveability.

Stage 3 — Who It Suits

Stage 3 is for the VE that's done more work. If you're running aftermarket heads, a higher compression ratio, or a converter swap is already on the list — Stage 3 makes sense. The extra duration pulls harder from 2,200 RPM onwards and rewards the top end. The lope is real and noticeable. This cam makes the car feel like a cam car.

It does not suit a stock short block with factory converter and an expectation of smooth low-speed driving. The converter becomes a problem — Stage 3 wants to be above 2,200 RPM, and a stock 4L60E converter stall will fight that at low speed.

Stage 3 verdict: Dedicated performance build. Heads, compression, converter work already done or planned. Car is primarily driven hard, not commuted.

The Converter Question

This is where most people get into trouble. A BTR Stage 3 with a stock factory converter will drive — but you won't get the gains the cam is capable of. The converter stall needs to match the RPM floor. If you're not ready to do the converter at the same time, do Stage 2 now and revisit when the rest of the drivetrain is sorted.

What IMS Does Differently

We install and dyno-tune BTR cams in-house at IMS in Morwell, Gippsland. We've done enough of these builds to know that cam choice without converter and tune consideration is how you end up with a car that's worse than stock at low RPM. We don't just sell the cam — we do the full job.

Before ordering, talk to us. Tell us the engine (L98 or LS3), what's already been done, and how the car gets used. We'll tell you which cam fits the build — not just which one sells more. Contact IMS | BTR LS camshaft range